Review of Clipper 29
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Clipper 29 or similar boat for sale
The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated.
The boat can enter even shallow marinas as the draft is just about 1.30 - 1.40 meter (4.27 - 4.57 ft) dependent on the load. See immersion rate below.
The boat is typically equipped with an engine.
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Clipper 29 is 1.93, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Clipper 29 is about 152 kg/cm, alternatively 854 lbs/inch.
Meaning: if you load 152 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 854 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Clipper 29 is 3.05.
The ballast ratio for Clipper 29 is 41%.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Clipper 29 with ISO 8666 reference sail is 13.1, with a 135% genua the SA/D is 15.7.
What is Relative Speed Performance?
The Relative Speed Performance for Clipper 29 is 10
Maintenance
Dimensions of sail for masthead rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 20.6 m | (67.4 feet) | 8 mm | (5/16 inch) |
| Jib/genoa halyard | 20.6 m | (67.4 feet) | 8 mm | (5/16 inch) |
| Spinnaker halyard | 20.6 m | (67.4 feet) | 8 mm | (5/16 inch) |
| Jib sheet | 8.3 m | (27.4 feet) | 10 mm | (3/8 inch) |
| Genoa sheet | 8.3 m | (27.4 feet) | 10 mm | (3/8 inch) |
| Mainsheet | 20.9 m | (68.4 feet) | 10 mm | (3/8 inch) |
| Spinnaker sheet | 18.3 m | (60.2 feet) | 10 mm | (3/8 inch) |
| Cunningham | 2.9 m | (9.5 feet) | 8 mm | (5/16 inch) |
| Kickingstrap | 5.8 m | (19.0 feet) | 8 mm | (5/16 inch) |
| Clew-outhaul | 5.8 m | (19.0 feet) | 8 mm | (5/16 inch) |
This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.
We are always looking for new photos. If you can contribute with photos for Clipper 29 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.