Review of Viksund Columbi 27
Basic specs.
Looking for a new boat? Find a Viksund Columbi 27 or similar boat for sale
Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The boat is equipped with 2+2 berths, a galley and 60.0 liter fresh water capacity.
Full keel
The Viksund Columbi 27 is built with a long keel. A full keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.
The boat can enter even shallow marinas as the draft is just about 1.10 - 1.20 meter (3.61 - 3.91 ft) dependent on the load. See immersion rate below.
The Viksund Columbi 27 has been equipped with different engine alternatives.
Alternative 1:
Viksund Columbi 27 may be equipped with an inboard Volvo Penta MD2 diesel engine at 16 hp (11 kW).
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
Alternative 2:
The boat may be equipped with an inboard Volvo Penta D1-30F diesel engine at 30 hp (22 kW). Cruise speed is 6.0 knots. Max speed is 7.0 knots.
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
Alternative 3:
The boat may be equipped with an inboard Leyland BMC 1800 diesel engine at 48 hp (35 kW).
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
The fuel tank, which is made of plastic, has a capacity of 80.0 liters (21 US gallons, 17 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Viksund Columbi 27 is about 153 kg/cm, alternatively 860 lbs/inch.
Meaning: if you load 153 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 860 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Viksund Columbi 27 is 2.82.
Maintenance
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 8.1 m | (26.4 feet) | 10 mm | (3/8 inch) |
| Genoa sheet | 8.1 m | (26.4 feet) | 10 mm | (3/8 inch) |
| Mainsheet | 20.1 m | (66.0 feet) | 10 mm | (3/8 inch) |
| Spinnaker sheet | 17.7 m | (58.1 feet) | 10 mm | (3/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Viksund Columbi 27 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.