The Thurø 33 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a long keel.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
The boat can enter most marinas as the draft is just about 1.77 - 1.87 meter (5.81 - 6.11 ft) dependent on the load. See immersion rate below.
Thurø 33 is typically equipped with an inboard Bukh DV20 diesel engine at 20.0 hp (14 kW), which gives a max speed about 5.1 knots.
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Thurø 33 is 1.78, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Thurø 33 is about 168 kg/cm, alternatively 944 lbs/inch.
Meaning: if you load 168 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 944 lbs cargo on the boat it will sink 1 inch.
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Thurø 33 is 28.4.
What is L/B (Length Beam Ratio)?
The l/b ratio for Thurø 33 is 3.30.
The ballast ratio for Thurø 33 is 43%.
What is Displacement Length Ratio?
The DL-ratio for Thurø 33 is 258 which categorizes this boat among 'light crusers & offshore racers'.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Thurø 33 with ISO 8666 reference sail is 14.4, with a 135% genua the SA/D is 17.3.
What is Relative Speed Performance?
The Relative Speed Performance for Thurø 33 is 46
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 30m2 (322 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
Dimensions of sail for masthead rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
Usage | Length | Diameter | ||
Mainsail halyard | 29.6 m | (96.9 feet) | 10 mm | (3/8 inch) |
Jib/genoa halyard | 29.6 m | (96.9 feet) | 10 mm | (3/8 inch) |
Spinnaker halyard | 29.6 m | (96.9 feet) | 10 mm | (3/8 inch) |
Jib sheet | 10.1 m | (33.0 feet) | 12 mm | (1/2 inch) |
Genoa sheet | 10.1 m | (33.0 feet) | 12 mm | (1/2 inch) |
Mainsheet | 25.1 m | (82.4 feet) | 12 mm | (1/2 inch) |
Spinnaker sheet | 22.1 m | (72.5 feet) | 12 mm | (1/2 inch) |
Cunningham | 3.2 m | (10.7 feet) | 10 mm | (3/8 inch) |
Kickingstrap | 6.5 m | (21.3 feet) | 10 mm | (3/8 inch) |
Clew-outhaul | 6.5 m | (21.3 feet) | 10 mm | (3/8 inch) |
This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.
We are always looking for new photos. If you can contribute with photos for Thurø 33 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.