Udkik.dk

Review of Jantar 23 Classic


Jantar 23 Classic
Jantar 23 Classic anno 1999.

Basic specs.

sail specifications
The Jantar 23 Classic is a small sailboat designed by the Polish maritime architect Andrzej Skrzat in the mid nineties.

Looking for a new boat? Find a Jantar 23 Classic or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Interior
The boat is equipped with 2 cabins, 4 berths and toilet facility.

Rig
The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

The boat can sail close to the beach as the draft is just 0.30 - 0.40 meter (0.98 - 1.28 ft) dependent of the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Jantar 23 Classic is 2.10, indicating that this boat would not be accepted to participate in ocean races.


EU classification

Jantar 23 Classic holds one CE certification:

If less than 5 in on board the boat is by European Union certified as Class C. INSHORE:
Designed for voyages in coastal waters, large bays, estuaries, lakes and rivers where conditions up to, and including, wind force 6 (Beaufort scale) and significant wave heights up to, and including, 2 m may be experienced.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Jantar 23 Classic is about 117 kg/cm, alternatively 660 lbs/inch.
Meaning: if you load 117 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 660 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Jantar 23 Classic is 2.66.

Slim Wide 69% 0 50 100
Compared with other similar sailboats it is more spacy than 69% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Jantar 23 Classic is 21%.

Low High 4% 0 50 100
This ballast ratio shows a righting moment that is higher than 4% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.


Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 6.6 m(21.7 feet)10 mm(3/8 inch)
Genoa sheet6.6 m(21.7 feet)10 mm(3/8 inch)
Mainsheet 16.5 m(54.1 feet)10 mm(3/8 inch)
Spinnaker sheet14.5 m(47.6 feet)10 mm(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Jantar 23 Classic it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References