Here we would have liked to show you nice photos of the Invicta 26.

If you have a photo you would like to share: Upload Image

If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Invicta 26 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Rig

The boat equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

The Invicta 26 is equipped with a long keel. A long keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.

The boat can enter even shallow marinas as the draft is just about 1.19 - 1.29 meter (3.90 - 4.20 ft) dependent on the load. See immersion rate below.

Engine

The boat is typically equipped with a Brit Sprite gasoline engine at 10.0 hp (7 kW), which gives a max speed about 4.7 knots.

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Invicta 26 is 1.70, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Invicta 26 is about 94 kg/cm, alternatively 527 lbs/inch.

Meaning: if you load 94 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 527 lbs cargo on the boat it will sink 1 inch.

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Invicta 26 is 24.8.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Invicta 26 is 3.61.

Ballast Ratio

The ballast ratio for Invicta 26 is 45%.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Invicta 26 is 259 which categorizes this boat among 'light crusers & offshore racers'.

SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)

Indicates how fast the boat is in light wind:

- Cruising Boats have ratios 10-15

- Cruiser-Racers have ratios 16-20

- Racers have ratios above 20

- High-Performance Racers have ratios above 24

Sail-area/displacement ratio (SA/D ratio): 19.98

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 16m^{2} (172 ft^{2}).

Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

Usage | Length | Diameter | ||

Jib sheet | 8.1 m | (26.4 feet) | 10 mm | (3/8 inch) |

Genoa sheet | 8.1 m | (26.4 feet) | 10 mm | (3/8 inch) |

Mainsheet | 20.1 m | (66.0 feet) | 10 mm | (3/8 inch) |

Spinnaker sheet | 17.7 m | (58.1 feet) | 10 mm | (3/8 inch) |

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Invicta 26 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References