Udkik.dk

Review of Hake 26RK


Basic specs.

sail specifications
The Hake 26RK is a sailboat designed in the mid 2000. The Hake 26RK is built by the American yard Hake Yachts, Inc..

Here we would have liked to show you nice photos of the Hake 26RK.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Hake 26RK or similar boat for sale

Hull
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Rig
The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Keel

The boat can sail close to the beach as the draft is just 0.38 - 0.48 meter (1.25 - 1.55 ft) dependent of the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Hake 26RK is 2.20, indicating that this boat would not be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.7 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Hake 26RK is about 127 kg/cm, alternatively 716 lbs/inch.
Meaning: if you load 127 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 716 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Hake 26RK is 12.4.

Low High 7% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 7% of all similar sailboat designs. This is a comfort value significantly below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Hake 26RK is 3.41.

Wide Slim 85% 0 50 100
Compared with other similar sailboats it is slimmer than 85% of all other designs. It seems that the designer has chosen a significantly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Hake 26RK is 34%.

Low High 18% 0 50 100
This ballast ratio shows a righting moment that is higher than 18% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Hake 26RK is 104 which categorizes this boat among 'ultra light racers'.

Heavy Light 96% 0 50 100
96% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 19.43


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 25m2 (269 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 8.7 m(28.4 feet)10 mm(3/8 inch)
Genoa sheet8.7 m(28.4 feet)10 mm(3/8 inch)
Mainsheet 21.6 m(71.0 feet)10 mm(3/8 inch)
Spinnaker sheet19.1 m(62.5 feet)10 mm(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Hake 26RK it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References