The Dawn 39 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
The boat can only enter major marinas as the draft is about 1.91 - 2.01 meter (6.27 - 6.57 ft) dependent on the load. See immersion rate below.
The boat is typically equipped with an inboard Yanmar 3HM 35P diesel engine at 30.0 hp (22 kW), which gives a max speed about 5.6 knots.
The fuel tank has a capacity of 151.0 liters (39 US gallons, 33 imperial gallons).
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Dawn 39 is 1.80, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Dawn 39 is about 211 kg/cm, alternatively 1183 lbs/inch.
Meaning: if you load 211 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1183 lbs cargo on the boat it will sink 1 inch.
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Dawn 39 is 29.6.
What is L/B (Length Beam Ratio)?
The l/b ratio for Dawn 39 is 3.48.
The ballast ratio for Dawn 39 is 48%.
What is Displacement Length Ratio?
The DL-ratio for Dawn 39 is 264 which categorizes this boat among 'light crusers & offshore racers'.
SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 22.05
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 37m2 (398 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
Usage | Length | Diameter | ||
Jib sheet | 12.0 m | (39.3 feet) | 14 mm | (0.55 inch) |
Genoa sheet | 12.0 m | (39.3 feet) | 14 mm | (0.55 inch) |
Mainsheet | 30.0 m | (98.3 feet) | 14 mm | (0.55 inch) |
Spinnaker sheet | 26.4 m | (86.5 feet) | 14 mm | (0.55 inch) |
This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.
We are always looking for new photos. If you can contribute with photos for Dawn 39 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.