Review of Scanmar 345

Basic specs.

The Scanmar 345 is a sailboat designed by the Swedish maritime architect Rolf Magnusson in the mid eighties. A few hundred boats have been produced. The Scanmar 345 is built by the Swedish yard Scanmar Yacht.

Here we would have liked to show you nice photos of the Scanmar 345.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Scanmar 345 or similar boat for sale

Hull

Both the hull and the deck is made of hand laid fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.

Interior

The interior is like many other boats made of mahogany.
The boat is equipped with 3 cabins, 7-8 berths, a galley and toilet facility.

Rig

The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Engine

The boat is typically equipped with an inboard Volvo Penta 2003 diesel engine at 28.0 hp (20 kW), which gives a max speed about 6.3 knots.

The transmission is a saildrive.

The fuel tank which is made of stainless steel has a capacity of 70 liters (18 US gallons, 15 imperial gallons).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Scanmar 345 is 1.99, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Scanmar 345 is about 198 kg/cm, alternatively 1109 lbs/inch.
Meaning: if you load 198 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1109 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Scanmar 345 is 22.6.

Comparing this ratio with similar sailboats show that it is more comfortable than 31% of all similar sailboat designs. This comfort value is just below average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Scanmar 345 is 3.11.

Compared with other similar sailboats it is more spacy than 62% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Scanmar 345 is 208 which categorizes this boat among 'light crusers & offshore racers'.

69% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Scanmar 345 with ISO 8666 reference sail is 17.5, with a 135% genua the SA/D is 20.3.

The SA/D ratio indicates that it is faster than 62% of all similar sailboat designs in light wind.

RSP (Relative Speed Performance)

What is Relative Speed Performance?

The Relative Speed Performance for Scanmar 345 is 66

The relative speed performance is 66 which means that a it is faster than 66% of all similar sailboat designs.

Maintenance

Rig

Dimensions of sail for fractional rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	33.5 m	(110.1 feet)	10 mm	(3/8 inch)
Jib/genoa halyard	33.5 m	(110.1 feet)	10 mm	(3/8 inch)
Spinnaker halyard	33.5 m	(110.1 feet)	10 mm	(3/8 inch)
Jib sheet	10.5 m	(34.4 feet)	12 mm	(1/2 inch)
Genoa sheet	10.5 m	(34.4 feet)	12 mm	(1/2 inch)
Mainsheet	26.2 m	(86.1 feet)	12 mm	(1/2 inch)
Spinnaker sheet	23.1 m	(75.8 feet)	12 mm	(1/2 inch)
Cunningham	4.2 m	(13.8 feet)	10 mm	(3/8 inch)
Kickingstrap	8.4 m	(27.6 feet)	10 mm	(3/8 inch)
Clew-outhaul	8.4 m	(27.6 feet)	10 mm	(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.

Finally

We are always looking for new photos. If you can contribute with photos for Scanmar 345 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.