Udkik.dk

Review of Naver 27


Naver 27
Naver 27 anno 1984. Viben


Basic specs.

sail specifications
The Naver 27 aka Junker 26 is a sailboat designed by the Danish maritime architect Arne Borghegn in the early eighties. The Naver 27 is built by the Danish yard Syd Thy Bådeværft.

Looking for a new boat? Find a Naver 27 or similar boat for sale

Hull
Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The deck is a double deck which improves the indoor climate.

Interior
The interior is like many other boats made of mahogany.
The boat is equipped with 5 berths, a galley and toilet facility.
Note: the boat has also been sold to be self-made/-interiored, which means that the quality of each boat may vary.

Rig
Rig
Rig of Naver 27.
The boat equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a genaker or a spinnaker for optimal speed.

Engine

Naver 27 is typically equipped with an inboard Bukh DV8 diesel engine at 8.0 hp (5 kW).

The transmission is a shaft drive. A shaft drive will in the long run require less maintenence than other types of drive e.g. a sail drive.

The fuel tank which is made of stainless steel has a capacity of 40 liters (10 US gallons, 8 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Naver 27 is 2.01, indicating that this boat would not be accepted to participate in ocean races.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Naver 27 is about 152 kg/cm, alternatively 851 lbs/inch.
Meaning: if you load 152 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 851 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Naver 27 is 3.02.

Slim Wide 54% 0 50 100
Compared with other similar sailboats it is more spacy than 54% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


RSP (Relative Speed Performance)

What is Relative Speed Performance?

The Relative Speed Performance for Naver 27 is 27

Slow Fast 27% 0 50 100
The relative speed performance is 27 which means that a it is faster than 27% of all similar sailboat designs.


Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 8.3 m(27.2 feet)10 mm(3/8 inch)
Genoa sheet8.3 m(27.2 feet)10 mm(3/8 inch)
Mainsheet 20.7 m(67.9 feet)10 mm(3/8 inch)
Spinnaker sheet18.2 m(59.8 feet)10 mm(3/8 inch)

Boat owner's ideas

This section shown boat owner's changes, improvements, etc. Here you might find inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what to look for.



Finally

We are always looking for new photos. If you can contribute with photos for Naver 27 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References